Skip to content

hw: enclosures for the v3.0 board, 18650 trough in the wall box, wall-box exploded view - #89

Merged
arcadien merged 8 commits into
masterfrom
hw/enclosures-v3
Nov 19, 2026
Merged

arcadien merged 8 commits into
masterfrom
hw/enclosures-v3

Conversation

@arcadien

@arcadien arcadien commented Nov 19, 2026 •

Copy link
Copy Markdown
Owner

Enclosures follow the v3.0 board (94.81 × 39.33 mm, 3 × M3, no on-board 18650 holder, J13 JST-XH).

Models

  • pcb.scad: pcb_v3() and pcb_v3_cropped() (cut at the x = 147 dotted line, 60.85 × 39.33); v2.2 models kept.
  • cell_cradle.scad (new): cell and tab-contact geometry shared by the mushroom cradle (unchanged: same volume and bounding box) and the wall-box trough.
  • Wall box: v3.0 board on 3 M3 standoffs; 18650 trough moulded on the floor, lighter version of the mushroom cradle (two tab contacts, two zip-tie saddles), leads W1 red / W2 black to J13 (JST-XH F). (sizes: see follow-up below). New render-only part="exploded". stand.scad / assembly.scad follow the new width .
  • Mushroom: cut v3.0 board, 2 × M3, 8 mm bosses; chassis 65.65 × 44.13 × 54.6 → chassis and gill disc to reprint; cap and dots unchanged.
  • Harness: W5/W6 end in a JST-XH (F) on J13 (RAW_IN); JP6 1-2 for address 0x76.

Follow-up: smaller wall box — it now holds the cut v3.0 board (2 × M3 + edge ledges; CR2032 part left out, a flat CR2032 box comes separately), trough below the board, cable bay merged, PG7 seated low; radio_flat (default) lays the 433 MHz module flat. Base 104.6 × 108.74 × 28.2 (was 117.61 × 122.74 × 36), cavity 83.8 × 63.93 × 25.8, mast 196 mm; W1 ~50 mm, W2 ~110 mm. Lid printed with rotate() instead of mirror(); lid screws M3 × 6.

Outputs and docs: all wall-box and mushroom renders, harness PDF (1 page A4), new docs/img/wallbox_exploded_iso.png in the README header (4th column), READMEs, WIRING, BACKLOG. PCB: cut-line dimensions on User.Drawings, obsolete y = 87 cut line removed (outline restored, DRC clean).

Review: one cross-check round found 10 mismatches (9 fixed; the 10th is below).

Not done

  • Orca projects (box.3mf, stand.3mf, mushroom.3mf) still hold the old meshes: enclosing/export.sh to run when you decide (it keeps the plates, but CLAUDE.md asks to warn first).
  • Flat radio module over J5/J8 and the 8 mm gland room next to the trough: not checked on hardware.
  • Not printed: trough contact fit and zip-tie tunnels, chassis fit of the cut board.

🤖 Generated with Claude Code

arcadien and others added 8 commits November 19, 2026 14:48
…ne removed, R5 reference hidden

Dimensions: 33.93 mm (left part, CR2032) and 60.72 mm (right part, kept
for the mushroom) on each side of the x = 147 dotted cut line. Board
outline (Edge.Cuts polygon) kept. DRC with schematic parity: 0 unconnected,
0 parity issues; only the SW1 library silkscreen warning remains.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- pcb.scad: pcb_v3() and pcb_v3_cropped() (cut at x = 147, 60.85 x 39.33),
  v2.2 models kept.
- cell_cradle.scad: cell and tab-contact geometry shared by the mushroom
  cradle (unchanged: same volume and bounding box) and the wall-box trough.
- Wall box: v3.0 board on 3 M3 standoffs; 18650 trough moulded on the floor
  (two tab contacts, two zip-tie saddles), leads to J13 (JST-XH); base
  117.61 x 122.74 x 36, lid 117.61 x 98.73 x 4; render-only exploded part.
  stand.scad and assembly.scad follow the new box width.
- Mushroom: cut v3.0 board, 2 M3 board screws, 8 mm corner bosses; chassis
  65.65 x 44.13 x 54.6; cap and dots unchanged (dome top pinned).
- Harness: W5/W6 end in a JST-XH (F) on J13 (RAW_IN); JP6 1-2 for 0x76.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
…wall-box exploded view

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
… README header

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
…blind pilot)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Cut board (60.85 x 39.33) on 2 M3 standoffs (MH2, MH1) and two edge
  ledges; CR2032 part left out (a flat CR2032 box comes later).
- 18650 trough below the board, cable bay merged; PG7 gland seated low in a
  20 mm counterbore beside the trough.
- radio_flat (default true): 433 MHz module lying flat, comp_h 17; the
  trough contacts set the depth.
- Base 117.61 x 122.74 x 36 -> 104.6 x 108.74 x 28.2, lid 104.6 x 84.73 x 4,
  cavity 83.8 x 63.93 x 25.8; mast 196.3 mm. Lid print orientation with
  rotate() instead of mirror().

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
…io, W1 50 mm / W2 110 mm, mast 196 mm

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
@arcadien
arcadien merged commit b015593 into master Nov 19, 2026
11 checks passed
@arcadien
arcadien deleted the hw/enclosures-v3 branch November 19, 2026 14:29
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Labels

None yet

Projects

None yet

Development

Successfully merging this pull request may close these issues.

1 participant